Skip to main content

MacBook Core 2 Duo Left Hinge Mount Replacement

What you need

  1. MacBook Core 2 Duo Left Hinge Mount Replacement, MacBook Core 2 Duo Left Hinge Mount Replacement: step 1, image 1 of 1
    • Use a coin to rotate the battery-locking screw 90 degrees clockwise.

  2. MacBook Core 2 Duo Left Hinge Mount Replacement: step 2, image 1 of 1
    • Lift the battery out of the computer.

  3. MacBook Core 2 Duo Left Hinge Mount Replacement: step 3, image 1 of 1
    • Unscrew the three evenly-spaced Phillips screws from along the rear wall of the battery compartment.

    • The screws are captive to the metal memory cover so you cannot lose them.

  4. MacBook Core 2 Duo Left Hinge Mount Replacement: step 4, image 1 of 1
    • Rotate the L-shaped memory cover so it clears the battery compartment opening and lift it up and out of the computer.

  5. MacBook Core 2 Duo Left Hinge Mount Replacement: step 5, image 1 of 1
    • Remove the following 3 screws:

    • One 11 mm Phillips#00 in the middle of the case. (Head: 5mm dia. x .75mm thick)

    • Two 14.5 mm Phillips #00 (Head: 5mm dia. x .75mm thick)

    • If the screws stick in the case, you can use a magnetized screwdriver to draw them out.

    • The shorter of the three screws goes in the middle.

  6. MacBook Core 2 Duo Left Hinge Mount Replacement: step 6, image 1 of 1
    • Remove the following 3 screws from the rear wall of the battery compartment:

    • One 3 mm Phillips #0. (Head: 2.75 mm. dia.)

    • Two 4 mm Phillips #0 on the either side. (Head: 2.75mm dia.)

    • Take extra caution with these screws as they can strip easily.

  7. MacBook Core 2 Duo Left Hinge Mount Replacement: step 7, image 1 of 1
    • Remove the two Phillips screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).

    • Two 6.25 mm Phillips #000. (Head: 4 mm. dia. x .5mm thick)

  8. MacBook Core 2 Duo Left Hinge Mount Replacement: step 8, image 1 of 1
    • Remove the four indicated Phillips screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.

    • Four 3.25 mm Phillips #000. (Head: 4 mm. dia. x 4mm thick)

  9. MacBook Core 2 Duo Left Hinge Mount Replacement: step 9, image 1 of 1
    • Remove the following 4 screws from the back of the computer:

    • The longer screws go on the inside, shorter screws on the outside.

    • Two 11 mm Phillips #00, with Shank (2.2mm dia. x 2 mm len.) (Head: 3.2 mm. dia. x .5mm thick)

    • Two 7.25 mm Phillips #00, with Shank (2mm dia. x 3.75 mm len.) (Head: 3.2 mm. dia. x .5mm thick)

  10. MacBook Core 2 Duo Left Hinge Mount Replacement: step 10, image 1 of 1
    • Remove the two Phillips screws from the optical drive side of the computer.

    • Two 5.2 mm Phillips #00, with Shank (2.3mm dia. x 3.5 mm len.) (Head: 3.2 mm. dia. x .5mm thick)

    • It is not necessary to remove the similar screws on the other side of the computer.

  11. MacBook Core 2 Duo Left Hinge Mount Replacement: step 11, image 1 of 1
    • There's a trackpad and keyboard ribbon connecting the upper case to the logic board, so don't pull the upper case off entirely just yet.

    • Starting near the display and working around to the front of the computer, pry up on the upper case. A or a medium hard guitar pick may help you to do this.

    • The upper case is likely to stick at the connection above the optical drive. If this is the case, first free all other sides, then proceed to pull upward on the upper case from either side of the optical drive opening.

    • If you stand the base on end to get a better look you may displace the total of 4 grey plastic clips that hold the keyboard in place. Don't panic. They slide into slots at the top right-most edge near the CD drive.

  12. MacBook Core 2 Duo Left Hinge Mount Replacement: step 12, image 1 of 3 MacBook Core 2 Duo Left Hinge Mount Replacement: step 12, image 2 of 3 MacBook Core 2 Duo Left Hinge Mount Replacement: step 12, image 3 of 3
    • While holding up the upper case, pull up the black tab of the silver cable away from its connector.

    • If there is no black tab, you can also use a spudger to gently pry the connector from its housing. This connector is tall, so be sure to pry straight up.

    • If you happen to break your upper case cable when removing the upper case, we stock the individually and we have a [invalid guide link] that makes replacing it easy.

    • While you have the upper case removed, you may want to take the opportunity to remove dust, hair, etc. It's best to use a can of compressed air, though if you use a brush, make sure that its bristles are made of a material (usually animal hair) that doesn't generate static electricity, which can destroy electronics.

    • Upon reassembly, there are 4 grey plastic clips on the optical drive side of the keyboard (refer to second picture). They must be installed in their slots for the keyboard to snap in properly.

    • To make the reassamble process easier, it's better to pull out the clips first by pulling it straight up gently. Be careful not to put too much strength because it will break.

  13. MacBook Core 2 Duo Left Hinge Mount Replacement: step 13, image 1 of 1
    • Remove the following 3 screws from the left hinge mount:

    • One 6 mm smaller diameter Phillips from the right side.

    • One 6 mm larger diameter Phillips from the middle.

    • One 10 mm Phillips from the left side.

    • Lift the hinge mount and attached plastic dust cover out of the computer.

  14. MacBook Core 2 Duo Left Hinge Mount Replacement: step 14, image 1 of 1
    • Slide the plastic dust cover out of its slot in the left hinge mount.

Conclusion

To reassemble your device, follow these instructions in reverse order.

System

Member since: 09/24/09

2,562 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 0

All Time: 2