Skip to main content

MacBook Unibody Model A1278 Hard Drive Cable Replacement

What you need

  1. MacBook Unibody Model A1278 Hard Drive Cable Replacement, MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 1, image 1 of 1
    • With the case closed, place the Unibody top-side down on a flat surface.

    • Depress the grooved side of the access door release latch enough to grab the free end. Lift the release latch until it is vertical.

  2. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 2, image 1 of 1
    • The access door should now be raised enough to lift it up and out of the Unibody.

  3. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 3, image 1 of 1
    • Be sure the access door release latch is vertical before proceeding.

    • Grab the white plastic tab and pull the battery up and out of the Unibody.

  4. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 4, image 1 of 1
    • Remove the following eight screws securing the lower case to the chassis:

    • One 3 mm Phillips screw.

    • Three 13.5 mm Phillips screws.

    • Four 3.5 mm Phillips screws.

  5. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 5, image 1 of 1
    • Using both hands, lift and remove the lower case off the upper case.

  6. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 6, image 1 of 1
    • Using the flat end of a spudger, pry the subwoofer connector straight up off the logic board.

  7. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 7, image 1 of 1
    • Disconnect the camera cable by pulling the male end straight away from its socket.

  8. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 8, image 1 of 1
    • Use a spudger to pry the optical drive connector straight up off the logic board.

  9. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 9, image 1 of 1
    • Remove the two Phillips screws securing the subwoofer to the upper case.

    • The longer of the two screws is on the right.

  10. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 10, image 1 of 1
    • The subwoofer is still connected to the right speaker, so don't completely remove it just yet.

    • Lift the subwoofer off the optical drive, and set it above the computer.

  11. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 11, image 1 of 1
    • Remove the two Phillips screws securing the camera cable bracket to the upper case.

    • The leftmost screw may remain captive in the camera cable.

  12. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 12, image 1 of 1
    • Remove the three 2.5 mm Phillips screws securing the optical drive to the upper case.

  13. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 13, image 1 of 1
    • Lift the optical drive from its right edge and pull it out of the computer.

    • The hard drive cable may become disconnected from the logic board when removing the optical drive. Ensure it is connected during reassembly.

  14. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 14, image 1 of 1
    • Remove the single Phillips screw securing the hard drive bracket to the upper case.

    • This screw is captive in the hard drive bracket.

  15. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 15, image 1 of 1
    • Lift the hard drive by its plastic pull tab and remove the freed hard drive bracket.

  16. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 16, image 1 of 1
    • Lift the hard drive out of its supports and disconnect the SATA cable by pulling the connector straight away from the hard drive.

  17. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 17, image 1 of 1
    • Remove the four 10.3 mm Phillips screws securing the mid wall to the upper case.

  18. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 18, image 1 of 1
    • Lift the mid wall out of the upper case.

  19. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 19, image 1 of 1
    • Use a spudger to pry the hard drive cable connector straight up off the logic board.

  20. MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 20, image 1 of 2 MacBook Unibody Model A1278 Hard Drive Cable Replacement: step 20, image 2 of 2
    • Peel the hard drive cable from the adhesive securing it to the upper case, and maneuver the plastic retaining block out of the upper case.

    • During reassembly, be sure the two pins on top of the plastic retaining block mate to the holes on the underside of the midwall.

Conclusion

To reassemble your device, follow these instructions in reverse order.

System

Member since: 09/24/09

2,562 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 0

All Time: 0