MacBook Pro 15" Unibody Mid 2010 Subwoofer & Right Speaker Replacement

Step 1 Lower Case

• Remove the following ten screws securing the lower case to the upper case:
• Three 13.5 mm (14.1 mm) Phillips screws.
• Seven 3 mm Phillips screws.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 2

• Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.
• Remove the lower case and set it aside.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 3
• Remove the two 7.4 mm Y1 Tri-Wing screws securing the battery to the upper case.
• Note: For certain repairs (e.g. hard drive), removing the battery is not necessary but it prevents any accidental shorting of electronics on the motherboard. If you do not remove the battery, please be careful as parts of the motherboard might be electrified.
• You do not necessarily have to follow steps 3-6 to remove the battery in order to replace the hard drive. However it is recommended to remove all power sources from electronics before working on them.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 4
• Use the tip of your finger to carefully peel back the corner of the warning label to reveal a hidden Tri-Wing screw.
• Remove the last 7.4 mm Y1 Tri-Wing screw securing the battery to the upper case.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 5
• Lift the battery by its plastic pull tab and slide it away from the long edge of the upper case.
• Do not try to completely remove the battery just yet.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 6
• Tilt the battery away from the logic board enough to access the battery cable connector.
• Pull the battery cable connector away from its socket on the logic board and remove the battery from the upper case.
• Pull the battery cable connector away from the center of the logic board.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 7
• Use the flat end of a spudger to pry the AirPort/Bluetooth ribbon cable connector up off the logic board.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 8
• Disconnect the camera cable by pulling its connector away from the socket (toward the optical drive) on the logic board.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 9
• Use the flat end of a spudger to pry the optical drive connector up off the logic board.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 10
• Remove the two Phillips screws securing the AirPort/Bluetooth board housing.
• Carefully rotate the AirPort/Bluetooth board housing (with AirPort/Antenna cables still attached) out of the lower case.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 11
• Remove the following three Phillips screws securing the optical drive to the upper case:
• One 4.5 mm Phillips screw securing the optical drive bracket to the upper case near the fan.
• Two 2.5 mm Phillips screws securing the optical drive to the upper case near the optical drive opening.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 12
• Lift the optical drive near its connector and pull it away from the upper case to remove it from the computer.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 13
• Use the flat end of a spudger to pry the hard drive/IR sensor cable connector up off the logic board.
• Peel the hard drive cable up from the channel within the subwoofer and right speaker.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 14
• Using the flat end of a spudger, pry the subwoofer connector straight up off the logic board.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 15
• Remove the following six screws securing the subwoofer and right speaker to the upper case:
• Two 3.2 mm Phillips screws.
• Two 12.3 mm Phillips screws.
• One 2.5 mm Phillips screw.
• One 8.3 mm Phillips screw.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 16
• Lift the subwoofer and right speaker assembly out of the upper case.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 17
• Before securing the AirPort/Bluetooth bracket to the upper case, be sure the small plastic tab on its left edge is inserted into the small void cut into the black plastic optical drive opening.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment

Author

System

Member since: 09/24/09

2,562 Guides authored

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

Preview