PlayStation 3 Slim PRAM Battery Replacement

Step 1 PlayStation 3 Slim PRAM Battery Replacement

• Turn the PS3 over and lay it on its backside.
• Carefully peel the warranty sticker up off the lower case to reveal a hidden screw cover.
• To avoid activating the VOID that may come up, heat the sticker carefully to remove and replace it cleanly.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 2



• Use the flat end of a metal spudger to pry up the seven screw covers around the edge of the lower case.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 3
• Remove the seven 37 mm Phillips screws securing the top cover to the lower case.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 4
• Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening. (Some models may only have three screws)
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 5
• Lift the top cover from its rear edge and rotate it toward the front of the PS3.
• Lift the top cover off the PS3.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 6
• Squeeze the AC inlet connector's locking mechanism and pull straight up to disconnect it from the power supply.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 7
• Pull the DC-Out cables straight up to lift their connector up and out of its socket on the power supply.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 8
• Remove the two 7.6 mm Phillips screws securing the power supply to the lower case.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 9
• Lift the power supply upward from its left edge as viewed from the front of the PS3.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 10
• Continue to lift the left edge of the power supply until it lifts off the two metal posts shown in the second picture.
• Remove the power supply from the PS3, minding any cables that may get caught.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 11
• If present, remove the pieces of tape securing the cables to the body of the Blu-ray drive.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 12
• Use the flat end of a spudger or your fingernail to flip up the retaining flap on the Blu-ray ribbon cable socket.
• Be sure you are prying up on the movable retaining flap, not the socket itself.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 13
• Pull the Blu-ray ribbon cable straight up and out of its socket.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 14
• Pull the Blu-ray power cable straight up to lift its connector out of the socket on the Blu-ray drive.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 15
• Remove the single 9.5 mm Phillips screw securing the Blu-ray drive to the lower case.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 16
• Lift the Blu-ray drive slightly by its right edge to dislodge the control board from its housing.
• Remove the Blu-ray drive from the PS3.
• After you reinstall the Blu-ray drive, be sure the control board is firmly seated in the lower case before proceeding.
• If replacing the Blu-ray drive with a new drive, swap the circuit board from your old drive into the new drive.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 17
• While holding the plastic retainer down against the board, use the tip of a spudger to pry the PRAM battery out of its housing.
• Failure to hold the plastic retainer down during the prying process may result in it tearing off the motherboard.
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment

Author

System

Member since: 09/24/09

2,562 Guides authored

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

Preview